Nema 14 Stepper Motor 35mm Body 1.8 ° 1A 2 Phase 4-Lead with 50CM Cable

works as expected on longer lk4 but does not work on cr10s4 ???? if anyone knows why please let me know

I purchased this to replace the stepping motor that came on my Ender 5 Plus. It had a press-fit gear so it wasn't compatible with my direct drive kit. Received this in no time and installed it even faster. It works just as good, if not better than the original Ender motor. My delivery came with a damaged wire but after contacting the seller, they replied the same day and offered to send me a replacement, which I received a two days later. Would easily buy from again.

This is for the 42-60 motor. Seems to be a good strong motor so far. For what it's worth to future readers, the instructions regarding the wiring aren't particularly clear. I installed this on an Ender 3 Max. After messing around swapping pins on my factory cable, first the two middle ones, then the red and green represented in the images. neither worked for me. I hooked up the cable that came with it without switching any pins and everything worked fine. The instructions could be more clear, maybe with an actual diagram.

Purchased this to build a watch cleaning machine using a stepper motor controller running in SPI mode and the motor runs silent with plenty of torque. I will purchasing a few more in the near future

I bought this motor (x3) hoping for a good replacement for a burned out bed motor and so far it seems to be working fine. You will need to uncross the center two wires on the connecting cable or you will get undesirable results. Switching the wires was the hardest part of this motor swap. No other setting changes were required.

Got this for my Creality CR10-S500 y axis. I swapped the middle two pins of the wire as described. Works only in very slow printing. If I increase to normal printing speeds, the rotor inside catches and makes a horrible sound, and sometimes will seize completely. If I turn the shaft by hand, I can feel shaft play as if the bearings are loose or there is too much tolerance, at some points in the rotation, the internals are catching. I am lucky this did not damage my printer when it seized. Returning this and I will try another brand.

Buena calidad

I should have grabbed a video but I was more concerned with immediate problems with the motor to do so. Out of the box it looked and felt fine. Installed it and realized my old motor had a catch that this one does not. That made me happy for a moment. I hooked up the cable from the original motor and tested movements; this failed entirely and started freaking out the printer with its inability to move. After closer inspection I discovered the negative pairs were BACKWARDS. Not the motor pins as a whole, just the negatives. This caused the motor to engage and disengage rapidly, shaking, and failingto do its job. After figuring this out, the motor is now being tested via a print over 12 hours; if anything happens or changes, I will update this. That being said, I have ordered thousands of motors for my work and many more for hobbies and printers, and I have never ever once recieved a motor with an inappropriately botched pair of grounds. I've had plenty that the groups were reversed from what I had, but that's not an issue of function and is not what I call an issue. TLDR the positive pins operate correctly and the negative pins are wired opposite of the norm, causing opposite polarity than it should after each attempted step (think 1 forward and 1 back over and over rather than each step moving forward ad it should), which made a total lack of movement and very bad engagement of the steppers.

Very well made and very powerful works well

3Dプリンタのトルク不足解消のため、全長47mmサイズの標準品から60mmサイズの本品へと交換。効果を感じられたので追加で購入しようと思いましたが、同サイズは取扱が無くなってしまったようで残念ですが購入できず、代わりに価格帯は違いますが国産の同型モーターを購入しました。

Bue producto

Ottimo motore, testato con encoder ad alta risoluzione. Nonostante le piccole dimensioni l'errore di passo è quasi inesistente. Utilizzato in micropassi per posizionare un condensatore variabile a piastre parallele. Il gioco assiale è dell'ordine dei micron quindi la meccanica è molto buona. Il rapporto prestazione/prezzo è notevole.

Mi serve uno stepper più potente di quelli che avevo a casa, e lo volevo con il connettore jst per non dover ricablare il progetto. E qui arriva la sopresa, il motore non gira ma vibra, pensavo fosse il driver che non riusciva ad alimentarlo e invece alla fine mi sono reso conto che il cavo fornito aveva un cablaggio lievemente diverso rispetto a quello di tutti gli altri stepper e quindi mi è servito ricablare comunque tutto. Detto questo è molto potente, e pesante quindi potrebbe essere necessario, a seconda del driver, variare anche la velocità massima degli stepper. Ma è comunque un eccellente prodotto.