(4 Pack) 532124959 124959 HD Switch Front Wheel Bearing Bushing to Bearing Conversion Kit fits Husqvarna, AYP, Poulan, Jonsered, Craftsman Sears Lawn Mower Garden Tractors

Perfect fit for the front wheels our Husqvarna TS120. Easy to install, came with replacement washers and spring clips as well. The bearings allow the wheels to roll like greased lighting now and will eliminate wear on the spindles since the wheels are no longer riding on bushings:) These were a very cost effective upgrade.

As advertised. Easy install.

Very well made. These are a VERY tight fit for a 3/4” spindle. You may have knock the paint off or sand it smooth before the bearings will slide on the shaft. Fit my YTH23K46.

After 5 years of hard use my left wheel was still doing great but the right wheel had developed some wobble to it. These bearing kits are only slightly more than the bushing kits, so figured it was worth doing. Hardest part of the whole job was knocking out the original bushings with a punch and hammer, but even that wasn't actually difficult. Clean up the old grease out of the hubs, put a thin layer of new grease on the OD of the bearings and they slide right in...don't even have to press them. Seem to be perfectly sized and no wobble despite not needing to be pressed. This kit includes all new washers and E-clips as well, plus the outer rubber boot. Easy and worthwhile.

I used the rubber boot. Bearings wouldn't fit the front axle shafts. Bearings were about . 2 thousandth too tight.

I installed these on the front tires on my yth22v46 riding mower. I've never maintained/greased the bushings, so I expected them to be quite worn out. I was glad to find the shaft wasn't damaged when I took the bushings off. These bearings were pretty easy to install. I just used a hammer and a long bolt I had to pop out the old bushings. Then, tapped these bearings in place on each side using a larger impact driver bit, to keep the pressure on the outside. They even fit in by hand most of the way, so lining them up in the wheel was pretty easy. I immediately noticed now smooth the wheels spun with the bearings in place. This is a great upgrade to my mower that I expect to extend the life of my wheels and axle. Getting replacement washers, lock washers, and dust boots was very helpful as well. I can easily recommend this product.

Put this on my Husqvarna YTH 18542 riding lawnmower wheels definitely spin more freely. The bearings fit perfectly into the steel wheel , came with all the accessories needed

Did a little "upgrade" on my 2015 husqvarna GTH52XLS tractor, while I was waiting on a few other parts. Used a metal bar and hammer to get the old bushings out, lightly sanded the spindles, used a shop press to push in bearings and installed. Took longer to clean out the old grease than to remove and replace bushings. After I was done with install, I pushed some grease through the zerks on the spindles to keep water out and help with lubrication. Not sure if I notice a difference, but tire spins 10x more freely. ID of bearings matched spindles well and had almost no slop. For the price and ease of install, it felt worth it.

Easy to change over, less than 5 minutes

This replacement worked so easily.

Very happy with this product, a perfect fit, so much so that you need to remove the old paint from the stub axle to slide the bearing on and they needed a drift to put them into the wheels. A vast improvement on the original bushings that lasted my mower just over 2 years from new and yes they were greased regularly the mower is only for domestic use so hasn't done many hours.

No problem installing these with basic tools. The old bushings need to be driven out and all the old grease removed. While no instructions come with this kit, if you keep track of the parts you removed taking the wheel off then reassembly is pretty obvious. Hopefully these will last a long time.

Easy to fit and didn’t need any special tools or knowledge. Has made the steering so much better.