Temporary tooth repair kit temp dental fix missing for 30 teeth! Triple!

In the midst of the COVID-19, the day after Easter, I lost the crown on a front tooth in a ham sandwich accident. I called my dentist, but unfortunately this was right after all dental offices were required to close. I did get a suggestion from them about a temp fix using a product that sticks crowns temporarily. That didn't work, and it was recommended to be used for only 48 hours any way. My next try was this product. I read the reviews and found the product for $9+ on Amazon.Note: You have to have existing teeth on either side for this to work so there are anchor points. If you are missing multiple teeth next to each other, this may not work.This stuff is amazing! It only took me a few bumbling tries to get a viable tooth replacement made. While it is a pretty bright white when set, I only needed a bit of a soak in really strong tea for a couple of hours to tint it pretty close to the right color. I don't know how much you can tint it if you need something darker, maybe coffee would work.Anyway, just a few hints. This sets pretty quickly so you have to use it immediately after heating. You can reheat it if necessary. Instead of letting it set up in my mouth, I used the tutorial that shows running the tooth under cool water for the final set. I also closed my mouth totally during the shaping stage to be sure the back of the tooth was comfortable with the lower teeth. The excess I ran up the roof of my mouth and a bit on the neighboring teeth. I trimmed up the edges to match the upper contour of the original tooth. It has virtually no taste so the gag factor can be kept to a minimum.Once it was all said and done, I ended up with something that looks a whole lot better than the gap left by the missing crown. It is easy to take out and reinstall, I can drink with it in, cool drinks anyway, and it stays in place when I talk. You should probably not eat with it in as it is just designed to fill a void, not as a working tooth, nor sleep with it because it could fall out and create problems.The kit came with three vials of beads, plenty to make multiple teeth.

DO NOT BUY THIS PRODUCT! Especially if you have a dental bridge or a cap. This product sounds good, videos look easy, but in my situation it was a nightmare! The formed tooth fell out of my mouth many times. I tried over and over again and followed video and written instructions. When a person is desperate to have a smile because the dental industry makes it virtually impossible to afford dental implants, this seems like a quick fix. IT IS NOT!!!!!! It can be dangerous, it says to let cool and harden in your mouth. If it hardens next to a bridge, it can pull it out! I had a tooth pulled, in my case, due to the dentist's mistake, and thought this would be a cosmetic fix when seeing family. It almost cost me tons of money from the damage it almost caused if I didn't think fast and use warm water to soften material in mouth to get it out. They promise 100% satisfaction. I called and they never returned my call or left me an email. So bottom line for me is...1) its a dangerous product, not meant for everyone. 2) if a person has any dental work that it will be next too, not a live tooth...DO NOT USE! 3) they lie about the 100% Guarantee. Nobody is home.BUYER BEWARE!

I received 3 vials of small plastic pellets, supposedly enough for 30 teeth. It's probably pretty close - 20-30 teeth, depending on size. The instructions say it takes about 15 pellets for a small tooth. I used closer to 25 for the tooth I replaced. This was a tiny fraction of one vial. Fortunately, if you get it wrong, you can simply reheat and try again. Adding pellets was seamless to the previous tooth.I was out of town and I used the coffee maker to make boiling water. Any source of hot enough water will work to soften the pellets. The pellets turn clear when heated and are easy to mold. I then molded them into a ball and put the ball into the space where my tooth was missing. It is important to fill ALL the space between the teeth, as there must be contact to keep it in place.The first try, I didn't use enough material and had to rework it. I just put the 'tooth' back into hot water, along with more pellets and reworked the material. This time, I spend more time making the tooth rounded on the surface, so it looked more natural. As noted, you can reuse the material simply by heating it. If you don't get it finished before it starts to harden, just put it back in the water for 10 sec or so and keep going. I used my fingernail to shape the tooth, which worked fine. The instructions recommend letting the tooth harden in the mouth, as this gives a better fit. If you don't get it right, just reheat and try again.I previously had a dental 'flipper' appliance, which cost $350. (I'm sure some dentists charge considerably more.) Neither the flipper nor the tooth created with this material are functional - not recommended to eat with. I did find that this tooth worked better when eating than the flipper. I'm sure the individual fit will impact that. This 'tooth' costs less than $1, rather than $350, and I found it more comfortable than the flipper. It does a great job as a cosmetic appliance.As others have noted, it is white, which won't match most teeth. The recommendations to let it sit in tea or coke seen reasonable, but I haven't tried either.I have used the 'tooth' for several weeks and have had no problems. After a while, it did seem to loosen a little. I'm sure that could be fixed by reheating and pushing it to fill the gap better. When I wear it, even my wife doesn't notice!

Expected a box as the image. The little balls and instructions came in a yellow envelope. Did not look very professional but as long as it works . I am ok with it.