RapidTac Application Fluid for Vinyl Wraps Decals Stickers 32oz Sprayer

This product is amazing! I make pictures from glass plates and always had bubbles in the vinyl that has to be attached first. No matter what I did. I always had bubbles, but not with this product. I seen a lady using it on U-Tube and she was having the same problem. Amazing product, especially for a beginner with a cricut machine. Made my life so much easier! Thanks

Revised 09-10-2023 ***I don't know what is going on, we reordered two bottles at a lower price, 11 days later still not delivered and now they want us to pay 7 dollars more a bottle for it if we reorder it***The product is great.Box needs to remain upright in transit.These bottles are known to leak.What is left in the bottle worked great.If you get some in the original box, it has arrows showing to keep it upright.It is a mild solution, but I recommend washing your hands good after using.I think this is one of the best brands on the market.

I can't say enough about this product. I was skeptical but decided to give it try as I had to replace the striping on my '89 Mustang GT. This stripe is a full inch wide and the last time I did it I used soapy water and the experience and finished result SUCKED!Rapid Tac isn't as slick on the panel meaning you can't slide the decal around for 20 seconds but you can pull up and reposition as long as you continue to saturate the panel during the process. Once in position, use the squeegee gentle to remove the air and liquid. That's it - your decal is STUCK! With soapy water, the decal has a tendency to lift or move even after you are certain that all the liquid is out.I don't know about all the other related 'Tac' products but I imagine they are just a good. Yes it's pricey but it's so worth it in the long run.

I was trying to adhere a laminate pouch to a glass cutting board. So many videos said get this product and use it. Apply to glass and add laminate pouch, then squeegee the liquid out. Let dry. Did this technique 3 times and couldn't get the laminating pouch to not come out cloudy and streaked. It did adhere the laminating pouch pretty decent, but hated the streaked look on the laminating pouch. It did not dry clear. Not sure I would use this over regular soap and water, which is cheaper!

if you do any vinyl application then you must get this - we have always use the Rapid Remover for taking old vinyl off and then we tried this product and we are in love with it - vinyl goes down - allows us to move and adjust it for a short bit but when it tac down it stays down - WE LOVE IT!!!

I was recommended this product by another jeeper. I had looked all over at places to put the decals on my wrangler, and was told it'd cost me 100 bucks an hour plus to do them. Finally, after getting the run around I asked my local jeep group what to do. A person recommended this product, told me to do a wet on wet application with it, and give it a try myself. People...I did it. A person with ZERO experience putting on huge decals actually did it and did a darn good job. The decals look amazing, the product worked great. Just make sure to copiously drench the vehicle area, and the decal, then scrape the heck out of the decal area to get the excess moisture out and tahdah. You also use this product to clean the area beforehand so it's the total essential tool for this. I posted a picture of my jeep and I used this on every single decal I did and I still have plenty left in the bottle and that was using copious amounts of it.

Easier installed

when you use this, it's going to take a loooooong time to get your sticker to adhere to the surface. but it's worth every aggravating second. follow the directions, put your sticker on the wet surface and set it how you'll want it, squeegee it out and walk away for 30 minutes to let it kinda dry, otherwise if your to quick nothing sticks. walk away..... you'll thank me after. once it's dried a little your transfer tape comes, your sticker sticks and it seems to stick better and last longer.