Motor Trend SpillGuard Waterproof Seat Covers for Front Seats, Gray Stitching – Durable Neoprene Car Seat Protectors, Easy to Install, Interior Covers for Auto Truck Van SUV

I purchase these seat covers as a gift for a family member. They fit her car perfectly easy install .

In order to be optimistic about these seat covers, one must be aware that there is the potential for the fit to be totally precise at the time of install. I knew this going in, so I'm also hoping that the fit will improve over time. These covers were purchased for my company car, a 2022 Toyota RAV4 and the install was easy, but a bit of aggravating. For starters, I was unable to push the bar of the covers through the crevice between the back of the seat and the lower part of the seat because there isn't an opening on the back for you to grasp the bar and pull the cover tight. Even so, I was able to push the bar down into the crevice. The second area of contention was the bottom strap that pulls the bottom seat cover tight. These straps go down the side of the bottom of each side of the seat and attach to each other with velcro. My problem with the directions were the fact that you aren't told whether you should go between the plastic trim or over it with the straps. Additionally, there are wires and a track for your seat to slide to the rear or forward that you must contend with. A bit of clarity around how you should route the straps would have been nice, but it definitely something you can figure out on your own. My primary concern is the overall fit. After my initial install, the fit is a bit loose on the bottom of the seat. It looks a bit bunched up and quite frankly - a bit sloppy. I'm hoping that this will tighten up a bit and look more fitted as time and use go by. Even so, for the cost, the covers seem to be made well and I'm sure they will keep my seats protected from the occasional spilling of coffee or salad dressing. As long as you aren't expecting professional quality fitted seat covers, you should be happy with the small amount of money that you'll pay for these covers.

ok received these today ,they came in a motor trend retail box.I bough to protect the front seats of a 1999 toyota sienna. they seem almost flimsy out of the box,however they actually feel durable after install . at $12.50 a seat,I was not expecting much. I first installed the headrest covers and it was like putting on a pillow cover. not much to it. then for the actual seat cover, it was a bit more involved,but I vaguely read the instructions on the box. After about 5-10 minutes I had it installed . The lower strap would not go under my seat as it is motorized,but I put it around the back.I then tucked the corners of the cover in between the chair and the plastic of the chair. Ok, it did not fit like a glove (but close) and left for a little play but this actually worked better as it kept the seat covers from coming off when entering/leaving seat and allowed you to move around in seat. When both were installed they look really great!! more importantly, they do protect the seat.As a smoker, I used to put down a blanket and that blanket was riddled with cigarette holes that would have gone on to burn the actual seat. After install, I see that these covers will protect even better than the blanket. Also, its fun and its like a new/different car. so, I recommend these highly, especially for the price!! Really nice. I tried sitting a few times and the seat covers did not budge or come loose. I;m buying a second set for my 2002 ford Taurus an maybe a third set for the back seats of the Toyota. the blankets I used to use just looked lousy and were coming off every time I entered or left the vehicle. This is such a better solution and looks so much better. will update after a while of use.Wow, for the price ,these are exceptional !!!

I wanted to protect the factory cloth seats in my Nissan Frontier and I thought this would be an economical solution. They look good. I took points off because they cannot be installed with the enclosed instructions. The seat back and seat on the Frontier are connected making it impossible to push the tube/holder between the seat and the back to stretch the cover in place. The seat track and frame covers also made it impossible to run the elastic seat band under the seat. I got the covers on but I could not get them as tight as I would have liked. Update: The side of the back slips off when you get in the seat. This is due to the way they are made to not interfere with the side air bag. Also the decorative stitching isn’t very tight allowing it to pull loose. Because of the material they are made of there is a lot of friction when you slide on to the seat. Still they are a good value for the price.

I was going to use this in a 99 ram 2500 Slt My vehicle info was already put into this site because I ordered a few parts for same truck. It gave me a green light "guaranteed to fit" Well I didn't realize that they weren't going to work until the time I had an opportunity to change a few other parts at the same time. Unfortunately it was outside my return window. So I've got a box of clutter lol. Instead of a new seat cover. And I need one bad. My truck has automatic seat, and the style seat in this model truck has no removable headrest. It's built into the whole chair. Just wish there was some way to still get this resolved, they r still brand new and I never woulda ordered if Amazon didn't say it would fit. Oh well. Thanks. Glad I spend whatever it is on prime every month for the good service.

These are not made of thin material. They are nice and thick on the back and bottom where your back and but make contact. The sides and back are thinner material that strech around the back of the seat and around the lower sides of the bottom of the seats. They will protect your seat very well from your kids and pets. The nice fitment on my wrangler jl seats are snug and very tightly conforming. Very pleased with the look and conforming fitment so far.

Filtered items for my vehicle, these seat covers "fit my vehicle" according to Amazon. The seat portion fits, however the back does not stay on when exiting the truck. It looks like an ill fitting halter top. Due to the construction of my seats, getting the velcro straps to wrap underneath in any direction was a challenge. My truck seats are not petite by any means. I recommend while attempting to place the back portion of the seat cover on, to set the headrest back on, to help keep the fabric in place. Otherwise you'll be tugging it off and losing your sanity over and over again. I do not recommend for anyone with a Ram truck, unfortunately these will have to torment me a little longer as we still have temps in the 20`s and 30`s overnight and my rear gets cold on leather seats. Once I find a replacement, I'll see if any co-workers want free seat covers. Will update with photos later as those are on a separate device.

So far so good. It fits really nice. Unlinked other seat covers this one actually goes the the shape of the seat. It is air bag compatible so that’s why the sides of the upper seat part is open. It feels amazing. I just installed (04/16/2019) and I haven’t had a problem with the material sliding or any problem with me having to readjust it when I get in and out. It hold very well. I drive my truck every single day so time will tell how long they last. For now I love them, they supply good padding, good protection, and good quality. I would have paid more than $30 for these. The headrest covers fit perfectly as well. No tearing what so ever. No stupid little clips just Velcro for the seat covers. Love them. FYI installed in a 2014 F150 FX4 (crewcab) with fixed center console (not like it matters lol).