Cross Comfort Golf Club Grip

These grips are very comparable to Dri Tac grips, they feel the same. I don't yet know about longevity, but Dri Tacs don't last very long from my experience, so the bar is set low. I was concerned about ordering these because of all the negative reviews stating how difficult they are to install. I have installed hundreds of grips, and have been using compressed air for the past 15 years or so. I wrap one layer of painter's tape around the shaft, dip black ring in mineral spirits (grip solvent) and use a tire inflator set to 60lbs to float the grip on the shaft. These did require a little more patience and effort, but still installed easily without any bunching up as shown in other reviews. If you haven't considered compressed air to install grips, take a few moments to watch a video or two. I've never had one rotate on the shaft or fail in any way. Plus, they come off just as easy !

I wanted to re-grip my granddaughters clubs with a comfortable, tacky golf grip. As with all things golf, grips have also gotten overly expensive. I don’t want to sound cheap because these grips are a great value and the real deal. Being familiar with Superstroke putter grips, their regular grips are on par with size, thickness, and comfort. My granddaughter loves the look and feel of these grips. In closing, this is the second set of grips of Superstrokes that I’ve purchased (I re-gripped my wife’s clubs last year) and I wouldn’t hesitate to buy them again.

Bottom Line: A key to install is coating the inside of the grip by plugging small hole end with a finger, add solvent, plug larger opening with other hand finger and swish back and forth while rotating the grip. Then empty solvent out the small hole into the grip over a paint tray. Details: The grips are great. Being soft grips, they will wear out quicker than Golf Pride, but I much prefer this feel. It’s similar to Dri-Tac. These are definitely harder to install. My struggles and then success: Attempt 1: First attempt was without a vise, as I have always done. I coated the tape in the shaft with solvent and then coated the inside of the grip by moving the solvent tip around the inner edge of the opening. I did not plug both ends and swish it back and forth (later realize this is a key mistake). I really struggled just to get the end of the grip over the edge of the shaft and then really struggled to get the grip on. All the “goo” from the tape was piling at the end as I pushed. I finally got it, but was risking bending my club head. Attempt 2: I ordered a vise that clamps to a desk because I don’t have a full work bench to mount one too. I mounted it to an old ikea cabinet I didn’t care about and followed a similar technique as Attempt 1. Fail. I got the grip about 2 inches on and it bent and that was it. Trash. I realized the cabinet wasn’t heavy enough to hold my force of pushing, but the key problem was there was still too much friction while trying to push the grip on. Attempt 3: Success (see pic) I moved the cabinet against the wall so I could push as hard as I could. I moved the vise closer to the grip end. I squeezed the black tip of the grip and rolled it to loosen it up in hopes it would get over the end of the shaft easier. Then I plugged the small opening of the grip with my left index finger and poured solvent into the grip by swirling it around the inner edge. Then I plugged the bigger opening of the grip with my right index finger and tilted the solvent in the grip back and forth while spinning it to completely coat the inside of the grip. Then I removed my left index finger and let the solvent drip onto the double sided tape on the shaft to soak it, catching it in a disposable paint tray. I quickly put on the grip, holding the shaft near the vise with my left had while getting the edge of the grip over the edge of the shaft with my right hand. Once on, I used two hands on the grip to push it straight on, and it went in one motion. I don’t need to twist at all. Then, if needed, just slightly straighten by rotating it. Success! I used this process with no issues for the rest of the clubs. I think the keys were loosening the tip of the grip by squeezing it in different directions and then the thorough coating of the inside of the grip by tilting back and forth is critical. Good luck! I almost returned them swearing the inner diameter was too small, but it’s not.

First thing is they look and feel amazing!! Really impressed. I had no issues with slipping and the comfort is A+ they do however wear down pretty quick. Admittedly I do play and practice frequently, but they did not last as long as I would hope. Especially with the clubs that I practice with a lot. If you play a couple of times a month with a few range sessions sprinkled in I feel that they would hit all the marks. If though you play and practice a lot the durability did seem a little lacking. Again the comfort is A+++

I have used these for 15+ years. They are the only grips I will use. With my first set of custom clubs 15 years ago, this is the grip my club maker recommended. Haven’t changed since then. The club maker even said that I really didn’t need to use a glove with these. I do keep them wiped down with a solution of Dawn dishwashing liquid and water after rounds. They seem to remain tacky forever. I play twice a week or more and these grips last over a year. There was a time I couldn’t find them 12 years ago and contacted the company and they sold them to me direct. Glad Amazon has them now. Give them a try.

After a year on my clubs these grips are still good. I really like the feel and takiness of them. I regrip my own clubs and these are as difficult as the others, glad they are lasting longer. I play a lot.

I had ordered these oversize grips in the past and I really like the feel and design. They installed easily. So I ordered two more a couple of months later to regrip two more clubs. I could not install them. To tight. I looked at comments and see others having the same problem. One said tight but if you work on it you'll get it on. I tried multiple times. So finally I measured the outside diameter of the (standard) shaft and the inside diameter of the grip. .090 of interference! Research shpwd it should be around .020 of interference and the tape, adds little more. No way these grips will fit! I didn't send them back, wasn't worth the effort for 12 or 13 bucks. I have them on my driver and 3 wood previously and they're great. But why take a chance on reordering and having them not fit.

These worked great for steel shafts but are terrible for graphite. They either would get stuck going on and I could not get them all the way on or they bubbled up from the force of pushing them on and caused bulges in the grip. I gripped one steel shafted wedge and it went on just like any other grips I have installed. However graphite shafts are a problem with these grips, I would avoid them if you have graphite shafts.

Macio mas não testei na humidade

I find these grips great, they have a great feel about them and the grip is non slippery, so great for all weathers, plus the price is very good to.

Buen agarre y material

値段の割には良品、少し表面がカサカサする。少しシットリ感が必要

Greifen sich sehr gut und lassen sich super aufziehen. Leider innerhalb von einer Woche um mehr als 20% im Preis gestiegen - sehr schade.