Dupli-Color HWP108 High Performance Wheel Paint - Gloss Black - 12 oz Aerosol Can

Beautiful color, high quality finish, spray can sprays amazingly with its thin atomization tip for nice even light coats. These wheels got a MATTE clear coat as requested by my customer, the normal gloss finish also looks incredible before they got the matte clear

Used this color on my Toyota aluminum wheels (applied epoxy primer first) goes on smooth and looks great. Highly recommend.

Love this gold spray paint. Easy to apply, high gloss, ultra smooth when dry.. The handle on our storm door was weathered and dingy looking. To purchase a replacement handle we would have had to buy a whole new lock set (cost would be about $70 plus shipping). However, thanks to this fabulous spray paint, we now have a lovely new looking storm door handle at a greatly reduced expense. The results were perfect. Dry to the touch in about 30 mins., so able to spray multiple coats and be done in an afternoon. Definitely well worth the price, and then some.

Not bronze! This is more "gold" than bronze. 6 years ago I bought this exact spray paint for my wheels on my subaru. They must have change the mixture slightly. Without turning this into a long story, I got new tires and the tire shop found one of my aluminum rims was severely cracked. I replaced the rim but it didn't match my other 3 rims. So I needed to paint it to the exact color which was this spray paint. I even found it in my Amazon order history. Bought it again, painted the rim, installed it and it looked off. Standing back it looked WAY different in color. Now I have to spray paint the other 3 rims to match. With that being said the paint is a great quality and still a beautiful sparkle color.

I used it to turn a polished carbon trim into a matte finish. Worked perfectly and had no issues. It’s over 3 years now and its still holding up pretty well.

Whether it’s DIY or in an automotive garage, this stuff is amazing and the gloss was like a mirror. I will admit when I use the 2K clear gloss acrylic. It changed the nature of the texture, but that could be the way it came out based on my distance of the spray. Hoping that helps.

Not bad am actually impressed, i will say this can turn out good with a proper preparation, cleaning wheels , primer, paint and clear coat, after 2 months nothing is peeling or falling apart.

Great buy! Perfect match for my sliver wheels. I currently had some curb rashes on my Enkei wheels. I decided to take it upon myself to do this simple DIY project. This can be down with the wheels still on the car, but much easier when they are off. You can easily touch up without needing to paint the whole wheel, it will blend nicely if done correctly. Things you will need:1)This paint 2) 220 & 400 Grit sandpaper 3) Wax and grease remover (or something to THOROUGHLY clean your wheels) 4) Glazing and Spot Putty (Depending how bad the curb rash or scratch might be) 5) MOST IMPORTANT some patience *The utmost important step is the prep work, you should spend a good amount of time prepping the wheel(s) for the paint. First, I used 220 grit sandpaper and sanded down the areas that I was planning on touching up (smoothing it out). Then, MOST important step is to THOROUGHLY clean your wheels with some wax and grease remover (or something safe on wheels of course, don't use just water and rag). Now your ready to fill in those scratches before paint, depending how bad the curb rash is or how deep the scratch(s) might be. I already had some "Glazing and Spot Putty" which is used on exterior of the car to fill in scratches. I confirmed that it was indeed safe to go ahead and use the "Premium Glazing and Spot Putty" on the scratches on the wheel. I actually had "Dupli-Color Automotive Touch-up Repair Kit" which came with the "Glazing and Spot Putty". Use your fingers to apply it on the scratch, thus filling it in. And use your finger to smooth it out. OR if you prefer to use something else like a card, go ahead. But personally I found it a lot easier and came out better when I used my fingers to apply the "Glazing and Spot Putty." Wait for it to dry (how ever long that might be), then your ready to sand it down once again. I had some 400 grit sandpaper which I used to re-sand down the area(s) where the putty was applied. Sand very lightly with the 400 grit, the idea is just to smooth out the putty you just applied and get out any excess putty that may have been over applied. Second to last step, is to once again clean your wheels to remove any excess dust from sanding and also any other dirt that may have shown up on the wheels as you were working with them. Lastly before your ready to paint, you will need to mask off a few areas before your ready to paint if your planning on leaving the wheels on the car. Tape around the wheel itself and also cover up the tire as well. Take a garbage bag cut it in half and make sure you cover your rotors and disc breaks etc. Now, your finally ready to paint. You don't need to apply any primer (only if your changing the wheel color.) Lightly spray the areas you've just been working on. Wait 10-15 mins inbetween each coat. Apply at least 3-4 coats. Wait about an hour or two before you use the car again. Oh yeah, Fast shipping as well! Haha

A bit sparkly but looks even after a few coats and overall effect looks good on the hubcaps.

Not what I accepted for the price I paid. Does not even come close to the chrome shine. Same as the 99 cent spray

Great product. A little pricey, but definitely worth it. Extremely pleased.

Has a sparkley/glitter like finish.

Great looking paint with good adhesion. Everything that’s gold in the photos was spray painted with this product.