4" Deep Well Submersible Pump 1HP, 230v, NEW AXIAL LOAD DESIGN, 242'head, 105PSI max, 22GPM, 2wire, Thermal Protection, stainless steel, 100% COPPER WINDING includes splice kit

This product works better than the original pump that was setup when we had our well drilled. We have never installed something like this before, but it was easy and quick. My water pressure is better than before. I will definitely be a return customer.

Started getting air in the lines and knew I needed a new pump ASAP. Found this one on Amazon. The price point made me skeptical. But decided to try it. It came super fast. Installed easy. (But I have done this before.) and it seems to be working great. It has been in service almost a year now. No issues. Buying another one for our retirement ranch.

Pump installed easily in my 4” well. Working as expected. Very quiet...it was hard to tell if it was running at first. Water pressure is great. Pump is 40ft down so I did not need an extra check valve.

This pump is manufactured in China but appears to be quality. I installed it about a month ago and so far it is operating perfectly. Time will tell regarding its durability. The included wire splice kit is very poor in quality so I chose not to use it. By providing it the vendor invites mistrust of the quality of the pump. Without the included splice kit, I would have rated the product 5 stars. I recommend the top quality wire splice kit available through Amazon at https://www.amazon.com/gp/product/B00E8S2ZR6/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

I replaced a pump that had been in use since 1992. I saw good reviews on this pump so decided to try it. What a big mistake. The straps holding the wiring which is too small , we’re flimsy steel that stuck out so far it was difficult to get it in the 4 inch well. After finally getting it installed I turned the water on to find that it only had 75% outflow that the previous pump had, same horsepower, same gallons per hour. After turning it off and back on to water the yard again I discovered the check valve didn’t work. I called the distributor and was told it was supposed to slowly loose its prime. Well long story short the pump only lasted for a year and so months so it has been replaced with an American Made pump that I am finally satisfied with.

I just received this product and noticed the check valve in the top did not have a rubber gasket or an O ring. I also noticed that it was not spring loaded. So I decided to pour water in the top before I installed it and it immediately drained through and out the bottom. I tried it again while putting pressure on the valve with my finger to hold it closed and it made no difference. The wiring also seems small and weak for such an electric motor. Ground wire was broke off upon arrival. I am going to buy another check valved and put on the top. I don't expect the pump last a long time from my observations. When it goes I will definitely pay extra for a better quality product.

HAVE NOT INSTALLED PUMP YET. OLD PUMP MAY HAVE CORRECTABLE PROBLEM (CHECK VALVE MAY HAVE BEEN 'TEMPORARILY' BLOCKED/STUCK, ALLOWING BACK FLOW AND SEVERE WATER HAMMER ON WELL PUMP), HAS SEEMINGLY CLEARED UP AND SYSTEM HAS RETURNED TO 'NORMAL' OPERATING RANGE(S).IF/WHEN PROBLEM RETURNS, THE 'SCHRAIBERPUMP' WILL BE INSTALLED, WITH ALL 'NEW PARTS' (250 PSI POLY DROP PIPE, SPACERS, TORQUE ARRESTOR, BRASS CONNECTORS AND WIRING); AND, IF DETERMINED NECESSARY, AN 'ALL METAL' BRASS IN-LINE CHECK VALVE.WHEN PUMP ARRIVED I CONDUCTED A GENERAL INSPECTION OF THE UNIT (CHECKING TIGHTNESS OF SCREWS, CLEAN / UNDAMAGED OUTLET THREADS, WIRING, CHECK VALVE, ETC.). I NOTED THE WIRING HAD BEEN FOLDED (FOR PACKING?). HOWEVER, WHERE THE WIRING CLEARS THE TOP EDGE OF THE PUMP BODY, THE WIRING HAD BEEN FOLDED INTO A BUNDLE (FOR PACKING?). THE FOLDED WIRE BUNDLE COULD NOT FIT INTO THE PACKAGING WITHOUT RUBBING THE WIRE INSULATION LOCATED AT THE VERY TOP OF THE PUMP BODY (MAKING IT DIFFICULT TO SPLICE AT THIS LOCATION IF THE 'RUBBING' FURTHER COMPROMISED THE OUTER INSULATION). FOLDING THE WIRING AT 'THIS' LOCATION FOR PACKAGING MAKES THE BUNDLE TO LARGE TO FIT IN THE PACKAGING WITHOUT RUBBING. SUGGEST MAKING A 'THINNER' BUNDLE WITH LONGER LOOPS THAT WOULD ALLOW THE 'BUNDLE' TO FIT INTO THE PACKAGING WITHOUT RUBBING.I ALSO NOTED THAT THE INTERNAL CHECK VALVE IS NOT ALL METAL, BUT APPEARS TO BE SOME TYPE OF NYLON PLASTIC. RECOMMEND CHANGING TO AN ALL METAL CHECK VALVE TO IMPROVE PERFORMANCE AND INCREASE PRODUCT LIFE.

Love the price and quality of the pumps.Will note that the install instructions that come with the pump make no mention of a separate check valve. One needs to be installed above the pump which is mentioned in the Amazon listing but not in the install instructions. Just a FYI. I found the tech support was great also!